How should daily maintenance of a hydraulic bending machine be performed?
May 25,2022
How to perform daily maintenance on a hydraulic bending machine?
CNC lathe, grinding tools, dust and metal material scraps. Check if the tools are securely installed. Abnormal electrical switches, cables, standard parts, loose wood. Before repairing or cleaning the CNC lathe, the lower mold should be aligned with the upper mold, and then learn to put down the spare parts until the work is finished. If switching machines or other actual operations are required, manual mode should be selected to ensure safety. The maintenance content introduced by the hydraulic bending machine manufacturer is as follows:
1. Gear oil circuit.
(1) Check the oil level in the car's oil tank every week. If the hydraulic transmission system is repaired, gear oil should be added.
(2) The oil should be changed after 2000 hours of use of the new mobile phone, and the oil tank should be cleaned every time the oil is changed after 4000 to 6000 hours of use.
(3) The temperature of the system software should be between 35 and 60, and should not exceed 70. If the temperature is too high, the oil and parts will mildew and damage.
2. Filter screen.
(1) The filter should be replaced or cleaned every time the oil is changed.
(2) If the hydraulic bending machine has a relevant alarm or other filter oil is not clean, it should be replaced.
(3) Check and clean the gas filter of the oil tank every 3 months, and replace it every year.
3. Parts of the hydraulic bending machine.
(1) Clean the parts (steel plates, valves, motors, pumps, oil pipes) of the hydraulic equipment every month to prevent dirt from entering the system software, and do not use cleaning agents.
(2) After one month of use of the new mobile phone, check whether the bent parts of each oil pipe are deformed. If there is any abnormality, it should be replaced. After two months of use, tighten all parts.
The wiring of the edge banding production and processing power supply follows the wiring method of the installation diagram, and performs pre-board wiring and waterproof sheath for the sheath line. The hydraulic bending machine manufacturer stipulates the following processing technology for pre-board wiring.
1. The relative path of wiring should be avoided as much as possible. Wiring should be processed in parallel on the same road, and classified and concentrated according to the main power circuit and control circuit. The plane cannot be divided, and the wiring should be close to the installation surface.
2. The height of the metal wire of the same plane flanging mold is consistent or consistent, and shall not be crossed. It is required that horizontal crossing cannot cross the position, but the route must be effective.
3. The wiring of the flanging mold should be horizontal and vertical, and evenly distributed. The steering machine is vertical.
4. When connecting the folding mold, do not damage the copper core cable and wire cable sheath.
5. Both sides of the open cable and sheath line are wrapped with copper shell. Ensure that the wires (or short wires) of all connecting terminals (or short wires) are connected, so that there will be no RF connector disconnection in the middle.
6. When connecting the wire to the terminal (or terminal), the sheath, rewinding and exposed copper of the cable cannot be too long.
7. Connect more than 2 wires to the connecting end of the electrical equipment components.
8. Check whether the wiring of the control box is correct according to the installation circuit diagram.
9. When installing the motor, pay attention to the connection method of the winding.
10. Use a connector to repair the plastic shell that connects the motor and the button (if it is a plastic shell, no connector is needed).
11. Connect the wires outside the control box, such as switch power supply motor.
Consult Now
Email:
Service Hotline:
Scan code to consult：
Sales Consultation
After-sales Service Consultation
More News
ONLINE CONSULTATION
Please consult if you have any questions, we will answer you as soon as possible! Thank you for your message
Contact Information：
Address: No.49 Jinghu Road, Huadu District, Guangzhou
Sales Consultation
After-sales Service Consultation
